Daewoo Washing Machine Error Code IE
WATER INLET ERROR
The water tap is closed.
The filter of the valve inlet is clogged.
The valve inlet is an inferior product or broke down.
The water level sensor (sensor pressure) is an inferior product or broke down.
The drain motor works during water supply.
The PCB ASS’Y does not check the water level.
Open the water tap.
Clean the filter of the valve inlet.
Change the valve inlet.
Change the water level sensor (sensor pressure).
Change the drain motor.
Change the PCB ASS’Y.
Daewoo Washing Machine Error Code OE
Daewoo Washing Machine DRAIN ERROR
The drain hose is kinked or clogged.
The drain motor is an inferior product.
The valve inlet works during drain.
The water level sensor is an inferior product.
The PCB ASS’Y does not check the water level.
Clean and straighten the drain hose.
Change the drain motor.
Change the valve inlet
Change the water level sensor.
Change the PCB ASS’Y.
Rearrange the laundry.
Daewoo Washing Machine Error Code UE
Daewoo Washing Machine UNBALANCE ERROR
The laundry is concentrated to one side of the drum during spin.
Rearrange the Cloths
Daewoo Washing Machine Error Code LE
Daewoo Washing Machine DOOR OPEN ERROR
The Start/Hold button is compelled while the door is opened.
Close the door of the Daewoo washing machine.
Daewoo Washing Machine Error Code LE
Daewoo Washing Machine DOOR OPEN ERROR
The Start/Hold button is compelled while the door is opened.
The switch door lock is an lower Washer .
The PCB ASS’Y does not check the door lock.
Close the door.
Change the switch door lock.
Change the PCB ASS’Y.
Daewoo Washing Machine Error Code E2
Daewoo Washing Machine OVERFLOW ERROR
The water is supplied endlessly due to an inferior valve inlet.
The valve inlet is normal, but the water level sensor (radar pressure) is inferior.
The drain pump dose not works. (The drain motor is an inferior product or broke down.)
Change the valve inlet.
Change the water level sensor (sensor pressure).
Change the drain pump.
Daewoo Washing Machine Error Code E4
Daewoo Washing Machine E4 LEAKAGE ERROR
Water leaks from the tub or the hose drain pump.
Check the leak of the tub or the hose drain. Then change the tub or the hose drain.
Daewoo Washing Machine Error Code E5
Daewoo Washing Machine E5 HIGH VOLTAGE ERROR
The laundry is blocked among the gasket and the drum.
The PCB ASS’Y is an inferior product.
Rearrange the laundry.
Conversion the PCB ASS’Y.
Daewoo Washing Machine E8 Error Code
Daewoo Washing Machine E8 MOTOR ERROR
The motor is not generally connected.
The motor does not work. (The motor is an inferior product or broke down.)
Check the connector of the motor.
Change the motor.
Daewoo Washing Machine E9 Error Code
Daewoo Washing Machine E9 SENSOR PRES- SURE ERROR
The water level sensor is an inferior product.
Change the water level sensor.
Daewoo Washing Machine H2 Error Code
Daewoo Washing Machine H2 THERMISTOR WASH ERROR
The thermistor wash is an lesser Appliance or broke down.
The thermistor wash is not associated normally.
Change the thermistor wash.
Check the connector of the thermistor wash.
Daewoo Washing Machine H4 Error Code
Daewoo Washing Machine H4 THERMISTOR WASH OVERHEATING ERROR
The heater worked without the water in the tub.
The thermistor wash is an less appliance or broke down.
Check the water level.
Change the thermistor wash.
Daewoo Washing Machine H5 Error Code
Daewoo Washing Machine H5 WATER TEMP. ERROR
The water fill-in, is over 45°C in slight & wool course. (The thermistor wash is an inferior appliance or broke down.)
Change the thermistor wash.
Daewoo Washing Machine H6 Error Code
Daewoo Washing Machine H6 HEATER WASH ERROR
The heater wash does not work.
(The water temp doesn’t raise over2°C during 15min.)
check the heater wash
Daewoo Washing Machine H8 Error Code
Daewoo Washing Machine H8 HEATER WASH OVERHEATING ERROR
The heater worked without the water in the tub.
Check the water level and the heater wash.
Daewoo Washing Machine Lb Error Code
Daewoo Washing Machine Lb IGBT ERROR
The PCB ASS’Y is an inferior product.
Change the PCB ASS’Y.
Daewoo Washing Machine PFE PUMP FILTER ERROR
Daewoo Washing Machine PFE PUMP FILTER ERROR
The PCB ASS’Y is an inferior product.
The drain pump filter is blocked.
The drain impel does not work during spin.
The large amount of detergent was used.
The drain hose is positioned higher than 1 m above the floor.
Change the PCB ASS’Y.
Clean the drain pump filter.
Change the drain pump.
Use the proper amount of detergent.
Place the drain hose 1 m below the floor
Daewoo Washing Machine Error Codes and their solutions
E9 This error occurs when the water level sensor frequency is over 30 KHz or below 15
KHz and also when the frequency is increased suddenly by more than 1.44 KHz in four seconds after filling up water. Water level sensor hose is off the position. (This feature will be applied later after reviewing in the future)
dE This error occurs if the door lock is not set to open or close when the door lock solenoid is operated more than 10 times. This error is cleared when the door is open.
LE This error indicates that the door opens during the operation of the washing machine. Procedure to handle this error. Close the door then the lock is engaged and the course continues
SE This error indicates that the safety switch is open right before entering the spin stage.
QE This error occurs when water is not drained for more than 15 minutes.
IE This error occurs when the water level sensor frequency does not change by more than 0.08KHz for 10 minutes after the start of water filling, and also when the water is not filled up for 60 minutes.
Procedure to handle this error: Open and close the door, check the water valve and water pressure, and press Start/Pause button, then the error is cleared and water will be filled again.
UE This error occurs when the unbalance switch is activated a third time after performing the unbalance operation (water fill + wash) twice during the spin stage.
Procedure to handle this error: Open the door, arrange the contents evenly, and close the door. Then the error will be cleared and spinning will be performed again
E5 (DC-Link High Voltage) Error
In case DC-link voltage to IPM increases to 450V or higher
Motor operation is stopped and ‘E5’ is shown in the display window.
Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
Error display is cleared when turning off/on power.
E6 (EMG) Error
In case current detected with EMG port is of 20A or higher
Motor operation is stopped and ‘E6’ is shown in the display window.
Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
Error display is cleared when turning off/ on power.
E7 (Direction) Error
In case signal of Hall IC is different from the predicted signal according to direction of rotation
Motor operation is stopped and ‘E7’ is shown in a display window.
Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
Error display is cleared when turning off/ on power.
E8 (Initial Operation Fail) Error
In case input signal of Hall IC is abnormal due to problems in motor connection, etc.
Motor operation is stopped and ‘E8’ is shown in a display window.
Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
Error display is cleared when turning off/ on power.
H2 Washing temperature sensor open/short
In case washing temperature sensor is defective or not connected
Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
Error display is cleared when turning off/on power.
H4 Washing temperature sensor overheating
In case temperature detected by washing temperature sensor is 95ᴱ or higher
Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
Error display is cleared when turning off/on power.
H5 Water temperature error in wool/delicate course
In case water temperature in wool/delicate course is 45ᴱ or higher
Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
Error display is cleared when turning off/on power.
H6 Abnormality in washing heater
Within 15 minutes after heater operation begins;
In case standard temperature is of 42ᴱ or lower: If temperature does not increase by 2ᴱ or more
In case standard temperature is higher than 42ᴱ: If temperature does not increase by1ᴱ or more
If the temperature falls below standard temperature by 2ᴱ or more due to re-supply of water, etc., standard temperature is reset as the current temperature and error check time of15 minutes is reset.
Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
Error display is cleared when turning off/on power.
H8 Washing heater overheating
In case washing heater temperature increases by 5ᴱ or more within 30 seconds when there is no water in tank, etc.
Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
Error display is cleared when turning off/on power.
b1 Motor alignment error
This error occurs when the alignment of the motor at the initial stage of motor operation is against the logic.
b2 Motor speed control error
This error occurs when the difference between the current speed and target speed is greater than 120 RPM.
b3 Low voltage error
This error occurs when the DC-LINK voltage is lower than 140V
b4 Motor startup overloading error
This error occurs when there is no hall sensor input within 400 msec at motor startup due to overloading or motor lock.
E1 Water level detection error
1) Conditions of Occurrence. In case water level is below reset or overflow is detected in line test mode
2) Water supply motor is kept on until water level falls below reset.
3) All LEDs are turned off and ‘E1’ blinks in 18:88 display.
4) Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
5) Error display is cleared when turning off/on power.
E2 Overflow error
1) Conditions of Occurrence. In case water level in water tank is above overflow level due to continuous operation of water supply valve
2) Water supply motor is kept on until water level falls below reset.
3) All LEDs are turned off and ‘E2’ blinks in 18:88 display.
4) Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
5) Error display is cleared when turning off/on power
E4 Water leakage during washing
1) Conditions of Occurrence. In case water level falls below re-supply even after 15 times of re-supply prior to finishing of water heating
2) All LEDs are turned off and ‘E4’ blinks in 18:88 display.
3) Error buzzer alarm is sounded for 10 seconds per every 10 minutes.
4) Error display is cleared when turning off/on power.